Choose Your Region and Language

NA
English
EMEA
English
LA
English
Asia
English

Regional Websites

Choose Your Region and Language

NA
English
EMEA
English
LA
English
Asia
English

Regional Websites

PI_150909_sz_sh_130_webgr

Intelligent Technology from STAHL CraneSystems Used For Aircraft Engine Maintenance

Aerospace | Hoisting & Lifting Equipment | by STAHL CraneSystems | March, 28 2019


GE Aviation, a division of the American conglomerate General Electrics, manufactures jet engines for aircraft. For maintenance of the highly specialized engines, a new plant with a state-of-the-art test laboratory was built in Três Rios, Brazil, in 2018, using intelligent technology from STAHL CraneSystems. STAHL Talhas, the Brazilian partner of STAHL CraneSystems, developed a sophisticated, highly automated solution for transporting engines through the facility’s halls and the testing area.

The GEnx engines of a Boeing 787 Dreamliner accelerate the 245-tonne aircraft to up to 945 km/h during take-off. To ensure the safety of the engines despite the extreme stresses, they must be serviced and overhauled regularly after 2,500 to 15,000 take-offs and landings. GE Aviation maintains various service locations worldwide for maintenance of its engines, including the company GE Celma in Brazil. 

More than 300 aircraft turbines are serviced at GE Celma’s main complex in Petropolis every year. The engines are dismantled completely, inspected, cleaned, repaired if necessary and then reassembled – a procedure that can take up to 65 days and involve over 12,000 parts. Every jet engine is tested under simulated flight conditions in a special test cell before it is put back into service.

The Dreamliner’s engine requires larger maintenance areas and more efficient test cells. For this reason, a new plant was built in Três Rios with one of the largest and most modern test bays in the world. The plant is equipped with comprehensive control technology for fast data processing, automatic fault diagnosis and real-time display of test results.

An Intelligent Solution
The intelligent crane and lifting technology used in GE Celma’s facility comes from STAHL CraneSystems and was installed by the company’s certified partner in Brazil, STAHL Talhas. The engineers and technicians from STAHL Talhas developed and built a highly automated custom transport system to manage the complete handling of the turbines – from unloading on arrival to transport to the maintenance stands and safe suspension in the turbine testing room.

“The complexity of the facility called for a high degree of technical sophistication,” said Sandro Galtieri, Managing Director of STAHL Talhas. “On the one hand, the low overall height of the plant posed a particular challenge for the development of the structural and mechanical design. On the other, the entire operating logic, including electrical design and software, placed high demands on our engineers. The hoists and cranes communicate with each other permanently to ensure that everything runs smoothly in the plant.”

The material handling system erected by STAHL Talhas consists of a central aisle, eight maintenance areas and a testing area. The engines must be transported safely from the central aisle to the eight maintenance bays on the right and left and into the testing area. The turbines in the central aisle are handled by a double girder overhead travelling crane with a lifting capacity of 40 tons.

In addition to this, STAHL Talhas installed a single-girder overhead traveling crane with a lifting capacity of 10 tons to transport turbine parts and components. The eight maintenance areas are equipped with monorails. The crane runways are connected by an interlock system for crane locking: a modern camera-based system detects the current position of the runways with the help of bar codes and automatically aligns them with a positioning accuracy of ± 1 mm. This ensures a smooth transition between the crane runways. The cranes and hoists are operated independently via radio remote control. “A special crane design was required to transport the turbines into the test cell,” said Sandro Galtieri. A monorail runway with a curved section was installed here.  

In all, four frequency-controlled SHF 60 wire rope hoists, each with a lifting capacity of 20 tons, and two frequency-controlled SHF 50 wire rope hoists, each with a lifting capacity of 5 tons, from STAHL CraneSystems were used. A selector switch on the radio control can be used to switch between tandem operation and normal operation of the hoists. All hoists are equipped with articulated trolleys for entry into the test cell. Since the height of the monorail runway beam in the turbine testing room drops from 400 to 245 mm and the internal beam height is then only 201 mm, a special low articulated trolley had to be designed for the SHF 60 wire rope hoists.

When entering the test cell, communication between the hoists and the locking system of the test cell is particularly important. In the passage to the testing room the monorail runway has a section that can rotate 90°. This section is motorized and has its own operator panel. The hoists can only enter the section if this section if the monorail is not rotated. The track section is released by means of specially developed sensors which communicate with the programmable logic controller (PLC) of the control panels. “The door of the testing room can only be closed when the rotatable section of the monorail is in rotated position. Here our system can also communicate with the customer’s own operator panel,” explains Sandro Galtieri.

During testing, the engine must be held by the integrated holding fixture of the test cell and not by the hoists. Using the slack rope monitoring function of the STAHL CraneSystems hoists, the control system recognizes the correct placement of the engines in the holding frame. Only when this is ensured are the support pins between the hoist and the suspension device released. The entire weight of the engine then rests on the support structure and the test can be carried out correctly.

In this new facility, an average of 700 engines will be tested per year and up to 12 engines prepared for testing in parallel. With expertise and components from STAHL CraneSystems, STAHL Talhas developed and built a state-of-the-art system for one of the world’s leading aviation companies. This is truly something to be proud of.

A double-girder overhead travelling crane with a lifting capacity of 40 tonnes is used to handle the turbines.

PI_190129_kt_kt_sl_114_web

The STAHL CraneSystems SHF 60 wire rope hoists are operated in tandem and are equipped with special articulated trolleys in a particularly low build.

PI_190129_sz_sl_sh_060_web

We use cookies to improve your experience on our site and to analyze site traffic. By continuing to use this website, you consent to the use of cookies in accordance with our Privacy and Security Policy.